Spyder Robotics
Herpstat 1 - Proportional Reptile Thermostat
From $239.95 was
5 in stock, ready to ship
Buy more, pay less
Each, for the whole order. Change the quantity below and the total follows.
A single-output proportional thermostat for one cage or one heat zone. The Herpstat 1 turns the heat down as the cage nears its target instead of switching it fully on and off, so temperatures hold steadier.
One output, up to 700 W
Dimming and pulse heating, with soft startup
Day and night temperatures, ramped over up to 10 hours
High and low alarms, and shut-off if the probe fails
Probe included; no Wi-Fi
Part number H1
Description
On this page
- 1 output
- 700 W
- 40 to 150 °F
- Day and night
- Probe included
- 1 year warranty
Why keepers choose it
A basic thermostat runs a heater at full power until the cage is warm, then cuts it, so the temperature swings above and below the target. The Herpstat 1 adjusts how much power the heater gets, which suits radiant heat panels, heat tape, heat mats, and dimmable basking lamps.
It controls one output from one probe. For two or more cages on their own settings, look at the Herpstat 2, Herpstat 4, or Herpstat 6. For browser monitoring and email alerts, choose the Herpstat 1 SpyderWeb.
At a glance
- Outputs
- 1
- Load per output
- 700 W
- Total load
- 700 W
- Temperature range
- 40 to 150 °F (4 to 65 °C)
- Control modes
- Dimming, pulse, cooling, lighting, humidity
- Humidity control
- With the optional probe, instead of heating
- Wi-Fi
- No
- Probes
- 1 temperature probe included
- Display
- Backlit LCD, °F or °C
- Power
- 120 V AC
- Warranty
- 1 year limited, from Spyder Robotics
How it controls heat
Proportional dimming lowers the power as the cage nears its target, for panels, heat tape, mats, and dimmable incandescent or halogen lamps.
Pulse mode varies the length of each powered interval instead. It can quieten the hum some metal racks make, but is not for visible basking lamps.
Soft startup brings a heater up gradually rather than at full power.
Auto Power Matching adjusts the response to how your cage holds heat, so a PVC cage and a ventilated glass tank are each held on target.
Day and night settings with a ramp between them of up to 10 hours, run on their own every day.
Tenths of a degree for the target and the display, in °F or °C, with sensor matching to adjust the reading if needed.
What the output can run
The one output does one job at a time:
Heating, in dimming or pulse mode.
Cooling, switching a fan on when the cage gets too warm.
Lighting, on a schedule, with sunrise and sunset fades for dimmable incandescent lights.
Humidity, with the optional humidity probe. The Herpstat 1 then controls humidity instead of heat, not both.
Safety features
High and low alarms, audible, at limits you set.
Probe failure detection shuts the output off if the probe fails or comes unplugged.
Safety relay and internal monitoring.
User-replaceable fuse, 6.3 amp. We stock spares.
High and low tracking records the extremes for you to check.
Memory keeps your settings through a power cut. Check the clock and schedule once power is back.
Setting it up
Put the Herpstat somewhere dry outside the cage, away from misting, condensation, and heat.
Plug in the probe and fix it at the spot it should control. Under an overhead heat panel that is usually below the panel; our probe mount holds it there.
Choose the mode for your heater, as its maker advises.
Plug in the heater. Keep it at or under 700 W.
Set the day temperature, then the night temperature and ramp if you want one.
Set the high and low alarms.
Let the cage settle, then compare the reading with a separate thermometer over a few cycles before you leave it running alone.
Our ReptiRad heat panels at 40, 80, 125, and 220 W are all well under the limit.
Useful with it
Sale
SaleSpyder Robotics
Replacement Fuse 3-pack (Herpstat 1 Basic, Herpstat 1, Herpstat 1 Spyderweb)
$8.95 was $9.99
In stock
Questions
What comes in the box?
The Herpstat 1, a temperature probe, a power cord, and the maker's documentation. Heaters are sold separately.
Can it control two cages?
Not on separate settings. It has one output and one probe. The Herpstat 2 runs two.
Can it control humidity?
Yes, with the optional humidity probe and firmware 5.2 or newer, but then it controls humidity instead of heat.
Does it have Wi-Fi?
No. For browser monitoring and email alerts, choose the Herpstat 1 SpyderWeb.
| Part number | H1 |
|---|---|
| Brand | Spyder Robotics |
| Shipping weight | 1.9 lb |
| Shipping box | 8.75 x 8.25 x 2.5 in |
Box size and weight are the packed carton, for shipping only, not the size of the item itself.
Shipping
Parcels across Canada and the US are priced at checkout from the packed boxes. Pallets and freight we price by hand, usually within one business day, and you pay nothing until you have seen the total. Pickup in Calgary is free.
Returns
14 day returns on eligible unused stock items, return shipping paid by the customer. Built-to-order goods are covered by the construction warranty rather than by returns. Restocking Fees Apply for returns
Warranty
One year warranty on the construction of anything we build.
Questions
Ask about it
Anything this page does not answer. We will get back to you as soon as we can, and good answers go up here for the next person.
Goes with it
Complete the setup
The rest of a arboreal snake kit. Or answer four questions and get the whole thing explained.
-
Enclosure
Cornel's World
2' x 2' x 4' PVC Reptile Enclosure - Tall Arboreal PVC Cage
From $424.00
Made to order · 4 options
-
Primary heat source
-
Ambient or secondary heat
Sale -
UVB
Sale -
LED lighting
Sale -
Substrate
More in Thermostats and monitoring
Sale
Sale
Sale
Sale
SaleExo Terra
Exo Terra 300 W Dimming & Pulse Proportional Thermostat - PT2461
$84.95 was $94.99
Only 3 left