15 in stock (can be backordered)
Original price was: CAD49.99.CAD46.95Current price is: CAD46.95.
Herpstat Steel-Tipped Temperature Probe is a 12-foot replacement sensor for compatible Spyder Robotics thermostats.
The steel tip responds quickly to temperature changes. In addition, its epoxy seal provides increased water resistance. Therefore, it is a useful replacement or spare for reptile enclosures, breeding racks and incubators.
Compatibility: Herpstat 1 Basic, Herpstat 1, Herpstat 2, Herpstat 4, Herpstat 6, Herpstat 1 SpyderWeb, Herpstat 2 SpyderWeb and many older models.
Important: Some early green-front Herpstat thermostats require an older probe. Contact us if you are unsure about compatibility.
15 in stock (can be backordered)
Reliable Replacement Temperature Sensor
12-Foot Cable • Fast Temperature Response • Epoxy-Sealed Steel Tip
Replacement sensor: Restores temperature readings on compatible Herpstat thermostats.
Steel-tipped design: Responds quickly to changes in temperature.
12-foot cable: Allows flexible placement in enclosures and rack systems.
Epoxy-sealed tip: Provides increased resistance to moisture.
Wide compatibility: Works with most standard and SpyderWeb Herpstat models.
Manufacturer: Spyder Robotics.
The Herpstat Steel-Tipped Temperature Probe is a replacement sensor for compatible Spyder Robotics thermostats.
It measures temperature and sends readings to your Herpstat controller. As a result, the thermostat can adjust heating equipment to maintain the selected temperature.
Unlike a standard plastic-tipped probe, this model features a steel sensor tip. Therefore, it responds more quickly when temperatures change.
In addition, the tip is sealed with epoxy for increased water resistance. This makes it useful in reptile enclosures, breeding racks and incubators.
A working temperature probe is essential for safe thermostat operation.
For example, a damaged or disconnected probe may prevent the thermostat from reading the enclosure temperature.
Fortunately, compatible Herpstat probes can be replaced without replacing the entire controller.
Therefore, keeping a spare probe available can help reduce downtime when a sensor needs replacement.
The steel tip transfers temperature changes faster than many standard probe materials.
As a result, the sensor can respond quickly when the surrounding air becomes warmer or cooler.
This feature is especially useful when monitoring air temperature in reptile enclosures or incubators.
The included cable measures approximately 12 feet long.
Therefore, you can place the thermostat outside the enclosure while positioning the sensor where it is needed.
For example, the cable can reach into a large PVC enclosure or across a reptile rack.
In addition, the extra length allows you to keep the thermostat away from moisture and animal activity.
Temperature probes use a sensor to measure surrounding conditions.
However, the material around that sensor can affect how quickly it responds.
The Herpstat steel tip transfers heat efficiently. Therefore, it can detect temperature changes sooner than some other probe designs.
As a result, it is a useful option for systems where air temperature changes need to be detected quickly.
The steel tip is sealed with epoxy to help protect the internal sensor.
Consequently, it offers increased resistance to moisture in humid reptile environments.
However, the probe is not advertised as fully waterproof. Therefore, avoid soaking it or placing it directly in water.
Breeders often rely on thermostats to control several enclosures or heating zones.
Unfortunately, probe cables can become damaged during cleaning or routine maintenance.
Keeping a replacement probe available makes it easier to restore a compatible thermostat when a sensor needs replacement.
Therefore, it is a practical spare part for reptile rooms and breeding facilities.
The Herpstat Steel-Tipped Temperature Probe works with many Spyder Robotics controllers.
However, some early Herpstat models require a different probe. Therefore, check your controller before ordering.
In addition, Spyder Robotics lists compatibility with several older controllers.
Some original Herpstat thermostats use an older sensor design.
Specifically, original green-front Herpstat controllers with serial numbers between 50101000 and 50102600 require an older probe.
Unfortunately, Spyder Robotics states that this older probe is no longer available.
Therefore, customers with these early models should confirm compatibility before purchasing.
Contact Cornel’s World with your Herpstat model and serial number. We can help you check compatibility before you order.
Many PVC enclosures use thermostats to control overhead heating.
Therefore, a working temperature probe is essential for proper temperature control.
The Herpstat replacement probe can be used with compatible thermostats controlling radiant heat panels and other heating devices.
Breeding racks often use heat tape or heat mats.
As a result, a reliable probe is needed to measure temperature and guide the thermostat.
The 12-foot cable also provides flexibility when routing the sensor into a rack.
Incubators require stable temperatures during egg development.
Because the steel tip responds quickly to air temperature changes, it is a useful choice for compatible incubator heating systems.
However, always verify incubation temperatures using an independent thermometer.
Larger reptile enclosures may require longer cable runs.
Fortunately, the 12-foot cable provides flexibility when positioning the sensor.
Therefore, the controller can remain outside the enclosure while the probe measures the selected area.
First, switch off the thermostat and disconnect it from power.
Next, allow connected heating equipment to cool before handling the probe.
Disconnect the old temperature probe from the thermostat.
Then, carefully remove the sensor and cable from the enclosure.
However, avoid pulling on the cable if it is secured behind enclosure panels or other equipment.
Insert the new probe connector into the appropriate Herpstat sensor input.
Next, confirm that the connection is secure.
Place the steel tip at the intended temperature-control point.
For example, an overhead heat panel setup may use a probe mounted below the panel.
However, the correct location depends on the enclosure design and heating method.
Route the cable away from sharp edges, doors and heating elements.
In addition, secure the probe so the animal cannot easily move it.
For PVC enclosures, consider using a compatible Cornel’s World probe mount.
Reconnect the thermostat to power.
Then, confirm that the controller displays a valid temperature reading.
Finally, compare the probe reading with a separate thermometer.
Allow the heating system to operate through several cycles.
As a result, you can confirm that the replacement probe and thermostat are working as expected.
For overhead radiant heat panels, our probe mounts are designed to position compatible sensors approximately 4–6 inches below the panel. However, always confirm the correct probe location for your heating setup.
A damaged or disconnected temperature probe may cause the thermostat to display an error.
For example, Spyder Robotics identifies several common sensor error messages.
A missing probe message may indicate that the sensor is disconnected.
First, turn off the controller. Then, check that the probe connector is fully seated.
If the problem continues, inspect the cable for damage.
A shorted probe message may indicate an electrical fault in the sensor or cable.
Therefore, inspect the cable for crushed, cut or damaged sections.
If the probe is defective, replace it with a compatible sensor.
An invalid temperature message may appear when the thermostat cannot read the sensor correctly.
First, check the probe connection. Next, confirm that the sensor is compatible with your controller.
If the error remains, contact Spyder Robotics for further support.
Spyder Robotics offers a probe exchange program for certain sensor failures.
Therefore, customers experiencing a shorted, missing or invalid temperature error may qualify for a replacement through the manufacturer.
However, eligibility is determined by Spyder Robotics.
Keep your temperature probe securely positioned below an overhead heat panel.
Our PETG probe mount helps prevent loose cables and accidental probe movement.
In addition, it provides a clean installation in compatible PVC enclosures.
Need a complete temperature controller?
The Herpstat 1 provides proportional heating and advanced temperature control for one heating zone.
Want to control two heating zones independently?
The Herpstat 2 offers two separate outputs with their own temperature probes and settings.
Need humidity readings instead of temperature readings?
The Herpstat Humidity Probe supports humidity sensing on compatible thermostat models.
However, it is a different sensor and does not replace a temperature probe.
It is a replacement temperature sensor for compatible Spyder Robotics Herpstat thermostats.
The cable measures approximately 12 feet, or 3.66 metres.
The steel tip transfers temperature changes quickly. Therefore, it can respond faster when the surrounding temperature changes.
The steel tip is epoxy-sealed for increased water resistance. However, Spyder Robotics does not specify a waterproof rating.
Yes. It is compatible with standard Herpstat 1 thermostats, except certain very early models.
Yes. The manufacturer lists the Herpstat 2 as compatible.
Yes. Both models are listed as compatible with this probe.
Yes. Spyder Robotics confirms compatibility with the Herpstat 1 SpyderWeb and Herpstat 2 SpyderWeb.
Yes, many older models are supported. However, original green-front units with serial numbers from 50101000 through 50102600 require a different probe.
Yes. The steel tip responds quickly to air temperature changes. Therefore, it is useful for compatible incubator systems.
Yes. When connected to a compatible Herpstat, the probe can monitor temperature for a radiant heat panel setup.
No. The probe only measures temperature. Therefore, it must connect to a compatible thermostat to control heating equipment.
Yes. Compatible Herpstat probes are removable. However, disconnect the thermostat from power before replacing the sensor.
First, check the probe connection and cable. If the error continues, the sensor may need replacement.
Yes. Certain probe failures may qualify for the manufacturer’s exchange program. However, eligibility must be confirmed by Spyder Robotics.
Yes. A spare can help reduce downtime if a probe becomes damaged or stops working.
Reliable Temperature Sensing for Herpstat Thermostats
12-Foot Cable • Epoxy-Sealed Steel Tip • Fast Temperature Response
Spyder Robotics • Replacement Temperature Sensor
BOX SIZE DIMENSIONS AND WEIGHTS FOR SHIPPING COSTS ONLY
| Weight | 0.3 lbs |
|---|---|
| Dimensions | 4 × 2 × 2 in |
No additional boxes are available for this product.
